SCE066001-V01是COG型OLED顯示器,分辨率72×40,SSD1306BZ IC,6800/8080接口,4線串行接口I2C,28針
型號:
SCE066001-V01Size (inch)尺寸(英寸):
0.66寸Resolution:
64×48Outline Dimension (mm):
18.46×18.1×1.21Viewing Area (mm):
15.42×12.06Active Area (mm):
13.42×10.06Interface:
6800/8080 Interface/I2C/ 4-wire SPIIC Part No.:
SSD1306BZColor:
Monochrome (White)PIN:
28FPC type:
Soldering
Basic Information
General Specification
ITEM | SPECIFICATIONS | UNIT |
MODULE SIZE | 18.46(W)x18.1(H)x1.21(D) | mm |
VIEWING AREA | 15.42 (W) x 12.06(H) | mm |
ACTIVE AREA | 13.42 (W) x10.06(H) | mm |
DOT SIZE | 0.19(W) x0.19(H) | mm |
DOT PITCH | 0.21(W) x0.21 (H) | mm |
ASSY.TYPE | COG | --- |
WEIGHT | TBD |
|
Interface Definition
PIN NO. | SYMBOL | TYPE | FUNCTION DESCRIPTIONS |
1 | NC(GND) | P | It should be connected to external ground. |
2 | C2P |
|
C1P/C1N-Pin for charge pump capacitor. C2P/C2N-Pin for charge pump capacitor. Connect to each other with a capacitor. They must be floated when the Charge pump not use. |
3 | C2N |
|
|
4 | C1P | I | |
5 | C1N |
|
|
6 | VBAT | P |
Power supply for charge pump regulator circuit. It must be connected to external source when charge pump is used. It must be float when charge pump is not used. |
7 | VSS | P | Ground pin. It must be connected to external ground. |
8 | VDD | P | Power pin for logic circuit. It must be connected to external source. |
9 | BS1 |
|
Interface selection pins. |
10 | BS2 |
|
|
11 | CS# | I | Chip Select input pin. Active "L" |
12 | RES# | I | Hardware reset input pin. Active "L". |
13 | D/C# | I |
This is Data/Command control pin. When the pin is pulled HIGH, the data at D[7:0] is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section. When 3-wire serial interface is selected, this pin must be connected to VSS |
14 | R/W# | I |
This is read/write control input pin. 8080: data write enable; 6800: read/write select pin. When serial or I2C interface is selected, this pin must be connected to VSS. |
15 | E/RD# | I |
This is read/write control input pin. 8080: data read enable; 6800: read/write enable pin. When serial or I2C interface is selected, this pin must be connected to VSS. |
16 | D0 | I/O |
These are 8-bit bi-directional data bus to be connected to microprocessor's Data bus. When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK. When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL. |
17 | D1 |
|
|
18 | D2 |
|
|
19 | D3 |
|
|
20 | D4 |
|
|
21 | D5 |
|
|
22 | D6 |
|
|
23 | D7 |
|
|
24 | IREF | I |
Current reference for brightness adjustment. This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum. |
25 | VCOMH | O |
COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
26 | VCC | P |
Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used. It must be connected to external source when charge pump is not used. |
27 | VLSS | P | This is an analog ground pin. It should be connected to VSS externally. |
28 | NC(GND) | P | It should be connected to external ground. |